2023-04-30 13:31:42 +02:00
|
|
|
# picoAM
|
|
|
|
|
A simple but capable AM transmitter for the Raspbery Pi pico!
|
2023-04-30 14:13:02 +02:00
|
|
|
|
|
|
|
|
|
2023-04-30 14:57:24 +02:00
|
|
|
(image deviates slightly from current version of the circuit, apologies!)
|
2023-04-30 14:13:02 +02:00
|
|
|
|
|
|
|
|
## Disclaimer!!
|
|
|
|
|
|
2023-06-11 12:39:45 +02:00
|
|
|
The Pi is, to my knowledge, not able to output enough power to disrupt anything significantly as long as you're not near an airport (if you
|
|
|
|
|
are, then it ABSOLUTELY IS), but with a long enough antenna, will get you in trouble and annoy others. Please use this only for experimental
|
|
|
|
|
and educational purposes and do NOT use this in a way which might cause any disruption!
|
2023-04-30 14:13:02 +02:00
|
|
|
|
|
|
|
|
My antenna for this is barely large enough for half of my room to have reception. Please don't go much further than that!
|
|
|
|
|
|
2023-04-30 14:42:45 +02:00
|
|
|
**Also**, this project will overclock your pi. However, 200MHz is fine for 99.9% of picos and is SUPER unlikely to damage it unless you
|
|
|
|
|
leave it running for a very long time (days or something in a closed environment).
|
|
|
|
|
|
2023-05-01 20:32:33 +02:00
|
|
|
### Most important disclaimer
|
|
|
|
|
|
|
|
|
|
Legal restrictions likely aren't enough for some people to not do this. Including me actually (tho minisenders with low power like
|
|
|
|
|
this are actually allowed where i live, but they have to be certified). However, there is one **EXTREMELY** importatnt thing to add:
|
|
|
|
|
|
|
|
|
|
This uses square waves, so there are GOING to be harmonics. One of those is near 99.6MHz, in the FM band. You will hear the sender there
|
|
|
|
|
as well in some cases as FM receivers *can usually* receive AM, its just gonna be really noisy. Your neighbors, sadly, might also hear it
|
|
|
|
|
there, as 99MHz FM is is in the FM radio bands. MAKE SURE YOUR ANTENNA IS SMALL!!!
|
|
|
|
|
|
|
|
|
|
There is also a MUCH STRONGER harmonic at ~155.726MHz FM, in the 2m amateur radio band. PLEASE, PLEASE, PLEASE don't use a large
|
|
|
|
|
enough antenna for it to be able to send that very far. And this signal will actually reach FURTHER than the AM one because it
|
|
|
|
|
is a shorter wavelength and therefore sends better using a short antenna. ***__PLEASE add the low pass filter I described.__***
|
|
|
|
|
|
2023-04-30 14:13:02 +02:00
|
|
|
## How it works
|
|
|
|
|
|
|
|
|
|
The Pi generates a 1557kHz PWM signal, which will be the carrier wave. The frequency is not changed, only the pulse width.
|
|
|
|
|
(Sadly, I was not able to make an FM version because FM would require more precise frequency shifts, which the pico just can't do.)
|
|
|
|
|
Then, an audio input is taken in on the right side of the breadboard (blue and green wire), which is clamped and slightly loaded
|
|
|
|
|
so that we don't get nasty interference.
|
|
|
|
|
Then, this clean signal is given to the pico on pin 26. The pico does pulse width changes according to the signal, and outputs the
|
|
|
|
|
AM signal on pin 15.
|
|
|
|
|
|
|
|
|
|
## Circuit Diagram and explanation
|
|
|
|
|
|
2023-05-01 21:25:15 +02:00
|
|
|
|
2023-04-30 14:13:02 +02:00
|
|
|
|
|
|
|
|
The part which prepares the audio for the pico is not strictly needed, but if you use line inputs, you reeeally should have it.
|
|
|
|
|
It has the following jobs:
|
|
|
|
|
- D1 and D2 clamp the signal to acceptable voltages
|
2023-05-01 21:28:18 +02:00
|
|
|
- **An extra resistor of about 50-400 ohms may be added from the AI+ point to the AI- point to load the signal.** This is optional, but
|
2023-04-30 14:13:02 +02:00
|
|
|
*can* clean up a little bit of noise if you have long cables.
|
|
|
|
|
|
2023-05-01 20:32:33 +02:00
|
|
|
**ERRATA :warning:**<br>
|
|
|
|
|
If you aren't an asshole, ***PLEASE*** add the low pass filter as mentioned in the Disclaimer:
|
2023-05-01 21:25:15 +02:00
|
|
|
- Add the 100ohm resistor (R3 in new schematic) between pico and antenna
|
|
|
|
|
- Wire a 2nF (2000pF) capacitor (C1 in new schematic) between the new start of the antenna and ground
|
2023-05-01 20:32:33 +02:00
|
|
|
|
2023-04-30 14:13:02 +02:00
|
|
|
## How to use it
|
|
|
|
|
|
|
|
|
|
- Flash the ino file using the Arduino IDE
|
|
|
|
|
- Cut open an audio cable and take one of the channels and the ground out of the cable's mantle
|
|
|
|
|
- Connect those to jumper wires
|
|
|
|
|
- Take a breadboard and put the pico on there, wire the circuit
|
|
|
|
|
- Add the audio inputs
|
|
|
|
|
- Add a **sufficiently long but not too long** antenna. Mine is about 2m-ish long.
|
|
|
|
|
- Connect the Pi to your PC using the USB port for power
|
|
|
|
|
- Connect the audio input to your PC
|
|
|
|
|
- Tune in to 1557kHz AM
|
